![]() ![]() right after I got it so I could use the VGA adapter I got with it, but when I tried to set it up (monitor, keyboard, and all) connected to the 3D printer, I ran into some issues. Besides the instructions themselves, another major intent of this article is just to say that yes, it works, and it doesn’t require a lot of convoluted process to set up. ![]() pretty much the only thing I found was “it should” and some references to running it on the Raspberry Pi. When I went looking to see if Repetier-Server would run on the C.H.I.P. If you are an experienced Linux user, this is a very straightforward process. ![]() I had been using Repetier-Host on my PC with its embedded Repetier-Server, so I really wanted to keep using the software as it was my favorite of the 3D printing apps I’ve tried so far. kickstarter a while back, and had a $9 computer I had played with for a while and then not gone back to, so it seemed like a great opportunity to put it to use. Select the desired webcam connection (JPG Images, MJPG Stream or JPG + MJPG Stream).Īt Reload Interval you can enter the polling interval for new images.Įnter your URLs in Dynamic Image URL and in Static Image URL and click Save Configuration.My wife got me a 3D Printer (the MonoPrice Maker Select V2) for Christmas, and while I initially had it connected directly to my PC, when I rearranged things it was no longer close enough to be practical to connect with a USB cable. These are the required URLs (replace with your ip address):ĭynamic Image URL: Static Image URL: In Repetier-Server open your printer and go to Printer Settings Webcam. Replace port by th eone of the webcam you want. If the mjpg server is on a different server then Repetier-Server, then you have to enter the network ip and port. If you are using Repetier-Server 0.80.1 or higher just restart the server and the webcams can be selected in webcam configuration. Here your ip address would be 192.168.2.3. With ip addr you find your ip address in such a line: ![]() Ports will change by doing this!Īfter installing the MJPG-streamer you need to get the local ip address of the server. etc/webcam_ports and restart all webcams. Just remember then to always use the same port or it will create a new webcam port. etc/nf to detect webcams by path instead of id. If you use identical webcams you might want to edit. Raspi-webcam is reachable over port 9000 while the usb webcams are reachable from ports 8080… in order of detection. Now installed webcams are running and can be viewed. Once you are satisfied with the setup, store configuration and proceed: So best is to avoid these webcams or use them with low resolutions only. Also note that some usb webcams do not support mjpg – these are supported but then the boards needs to compress images to jpg increasing the load. If delay builds up you will get problems and should reduce traffic. So check if images get submitted with only small delay. But keep in mind that larger images and higher frequencies mean more traffic and that can get a problem. Frame rate and resolution be changed if you think it is required. The last 3 lines should match where you installed mjpg_streamer and should match if you followed the instructions. If set to yes it also watches for a special pi cam and that will fail on non pi systems. Especially set IS_PI to no if the board is not a raspberry pi. Then edit the configuration to your situation. Now it is time to install our special start and watch scripts. Sudo apt-get install libjpeg8-dev imagemagick libv4l-dev v4l-utils make gcc git cmake g++Ĭd mjpg-streamer/mjpg-streamer-experimental/Ħ. Last nice thing about this installation is that since Repetier-Server version 0.80.1 the server will recognise the webcams and offer them in a dropdown list for simple assignment. This solution will install mjpg_streamer such that it automatically starts a server when you insert a webcam and even starts a second instance if you add a extra webcam. The description is valid for debian jessie, but should work on other current distributions as well. Here you find a detailed description how to install MJPG-streamer. Feel free to use other software as the one described here. You can use special IP webcams or a simple software, turning your webcam into a streaming webcam. To use a webcam inside Repetier-Server, you need to stream the data as JPG or MJPG. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |